2000 Honda passport no start

Discuss anything related to drivetrain problems here (Engine, Transmission, etc)

Moderator: Staff

2000 Honda passport no start

Postby paul6165 » Tue Apr 27, 2021 11:09 am

Replaced head gasket rh eng cranks no start (2000 honda passport) getting fuel press 1st question on LH side 3 connector one goes to cam position sensor another to a valve with hoses no place to connect other one any ideas. I have noid lights. Picking up Cam Sensor just because so hard to change will also pick up spark tester that will hook up to Coil pack. Probably wiring harness due to moving around during tear down. Was going to do both but elected to only do one side had head press tested for flatness both good.
What I need is ideas to test certain things and wire color for for things that would control spark and inj signal. Just purchased man what a engine 170,000 no ridge in cylinder sleeve no sign of oil burn did clean out egr tube.
Any help would be greatly app.

Paul
paul6165
Drives on Pavement
 
Posts: 8
Joined: Tue Apr 27, 2021 10:40 am
Has thanked: 0 time
Have thanks: 0 time

Sponsor
 

Re: 2000 Honda passport no start

Postby paul6165 » Tue Apr 27, 2021 4:51 pm

Up date installed cam sensor getting (spark removed one the coils and held next to intake) used noid light no signal while cranking using multi meter measured over 12 volts signal to injector connector with just key in on position. Anyone have wiring dia between cam sensor and computer to ck signals?
paul6165
Drives on Pavement
 
Posts: 8
Joined: Tue Apr 27, 2021 10:40 am
Has thanked: 0 time
Have thanks: 0 time

Re: 2000 Honda passport no start

Postby Buster28 » Tue Apr 27, 2021 7:20 pm

The a 98-99 dohc 3.2L engine does not need a functioning Camshaft Position Sensor (CPS) to start and run. The CPS determines the first cylinder that should fire on startup, it takes longer to start if the CPS is not working.

00-04 3.2L have an Ion Sensing Ignition system installed and the CPS function is built into the Ion Sensing Ignition Module. I am reasonably sure the CPS in your truck is being used as a blanking plug and is not being used in the startup sequence.

The Ignition and injector control pulses are controlled by the Crankshaft Position (CKP) Sensor. The CKP output signal is called 58X because 58 pulses are generated each crankshaft rotation.

Was this engine running just before you replaced the head gasket?
2002 Rodeo Sport 4X4 3.2L V6
2020 Jeep Wrangler 2dr 4x4 3.6L V6
User avatar
Buster28
4L30E Guru
 
Posts: 11529
Joined: Fri Dec 18, 2009 12:28 pm
Location: RI
Has thanked: 10 times
Have thanks: 1312 times

Re: 2000 Honda passport no start

Postby paul6165 » Tue Apr 27, 2021 8:28 pm

Yes truck was running where is crank sensor off of crank a ring that fits onto crank right.
paul6165
Drives on Pavement
 
Posts: 8
Joined: Tue Apr 27, 2021 10:40 am
Has thanked: 0 time
Have thanks: 0 time

Re: 2000 Honda passport no start

Postby Buster28 » Wed Apr 28, 2021 3:48 am

paul6165 wrote:Yes truck was running where is crank sensor off of crank a ring that fits onto crank right.

The Crankshaft Position (CKP) sensor is located on the RH side of the engine block by the motor mount attachment.
Did you follow this procedure when you installed the timing belt?
Isuzu training video (after ads play)
https://www.youtube.com/watch?v=4st6CqDGmoc
2002 Rodeo Sport 4X4 3.2L V6
2020 Jeep Wrangler 2dr 4x4 3.6L V6
User avatar
Buster28
4L30E Guru
 
Posts: 11529
Joined: Fri Dec 18, 2009 12:28 pm
Location: RI
Has thanked: 10 times
Have thanks: 1312 times

Re: 2000 Honda passport no start

Postby paul6165 » Wed Apr 28, 2021 8:51 am

Yes I did follow that process.
paul6165
Drives on Pavement
 
Posts: 8
Joined: Tue Apr 27, 2021 10:40 am
Has thanked: 0 time
Have thanks: 0 time


Who is online

Users browsing this forum: Google [Bot] and 32 guests